You are here: > Home > News > Industry News

Operation of the wrench

source:Industry News release time:2022-12-06 Article author:yu Popular:Air band saw

  AN21-550 Pneumatic nut runner

  Pay attention to the position of the reversing switch before operation, so that you can know the direction of rotation when operating the intake valve

  Be sure to ensure the compressed air entering the air motor of the wrench: clean and dry air with a maximum pressure of 6.0bar. Otherwise, it may/unavoidably lead to dangerous situations such as driveline failure, overspeed, rupture, wrong output torque, etc.

  Make sure all hoses and other connections are correctly sized and securely installed; do not use damaged, worn or aged air hoses and other connections; it is recommended that an emergency shut-off valve be installed on the air supply line and that others Find out where it is installed.

  Before operating the machine, be sure to check that there is enough lubricating oil in the oil cup. Lack or no lubrication will accelerate air motor blade wear, resulting in reduced tool performance and increased maintenance.

  The body posture must be balanced and stable, and the tool should not be operated too much. When turning on and operating the tool, prevent and be alert to sudden changes in torque and force in motion.

  In the event of a hose failure or broken connection, install an appropriately sized air safety device upstream of the hose and use a stabilizer through any hose connection to prevent the hose from wobbling without shutting off the inside of the hose.

  This tool is a torque tool with a reaction arm. The huge torque generated by the machine is absorbed by the reaction arm.

  Therefore, it is necessary to find a supporting point of sufficient strength for the reaction arm during operation. In view of safety considerations, when the machine is working, be sure to stay away from the working range of the reaction arm, otherwise, it may/unavoidably cause huge personal injury.

  (Q)PTW series pneumatic torque wrench achieves precise torque control by adjusting the mechanical gear, air source processing components, and power management system. The operations are as follows:

  Mechanical gear: check the torque comparison table, and adjust the shift knob to 1st or 2nd gear.

  Adjust the air supply pressure to the required pressure as follows.

  Lift the adjusting nut up and turn clockwise to increase pressure and counterclockwise to decrease pressure.

  After adjusting to the working pressure, be sure to press down the pressure regulating nut to fix it.

  When adjusting the pressure, there will be a small amount of leakage, which is a normal phenomenon.

  Referring to the torque comparison table, adjust the power adjustment knob to the appropriate position, 1 is the minimum, 4 is the maximum.

  This system allows the operator to reduce the maximum output power in the forward direction. But the power management system has a reverse

  output power is not affected.

  The power level indication is for reference only and does not indicate specific power. Using a variable stem, it is possible to

  to further adjust the forward or reverse output power.


Read recommendations:

DM22-016 Rail Drill

LH61-010 Emulsion Hoist

Tool Bits

Carborundum Saw Chains

How to identify the quality of hydraulic oil for hydraulic wrenches.https://www.biimpact wrench sale

Previous:Introduction to the principle of pneumatic wrench Next:Hydraulic chain saw

related articles

What to do if the pneumatic wrench is weak

2022-12-19

Hydraulic chain saw

2022-12-13

Operation of the wrench

2022-12-06

Introduction to the principle of pneumatic wrench

2022-11-28

How to use the pneumatic wrench

2022-11-21

Brief introduction to the principle of pneumatic wrench

2022-11-14

Impact pneumatic wrench

2022-11-07

Correct hydraulic wrench operation procedure

2022-11-01

Hydraulic wrench torque pressure conversion

2022-11-01

Field operation procedure of hydraulic wrench

2022-10-24

Hydraulic radial plunger motor

2022-10-17

The history of hydraulic motors

2022-10-17

Principle of balance hydraulic wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Introduction to the advantages of using intelligent electric torque wrench

2022-10-10

The Price Factor of Smart Electric Torque Wrench

2022-10-10

Classification and use of wrenches

2022-10-10

hydraulic wrench pressure conversion

2022-10-10

Introduction to the advantages of the use of intelligent electric torque wrench

2022-10-10

Smart Electric Torque Wrench Selection Guide

2022-10-10

Intelligent electric torque wrench for wind power generation

2022-10-09

Uses of open-end wrenches.Pneumatic chainsaw

2022-10-08

What are the driving parts of a hydraulic wrench and what they do

2022-09-30

What are the driving parts of a hydraulic wrench and what they do

2022-09-23

the commonly used wrenches

2022-09-22

Introduction of several common wrenches

2022-09-21

Application scope and daily maintenance method of hydraulic bolt tensioner

2022-09-20

Characteristics of hollow hydraulic wrench and precautions for use

2022-09-19

Characteristics and precautions of driving hydraulic wrench

2022-09-17

Selection of hydraulic jack

2022-09-16

Power Tools

CB21-190丨Pneumatic Mining Chainsaw/Pneumatic Band Saw - Aluminum Alloy Series

2023-01-06

AN51-3000 Electric servo CNC Torque Wrench

2023-06-27

AW41-3500丨Emulsion Impact Wrench

2023-06-21

GP61-200 Emulsion Submersible Pump

2023-06-29

RH31-1550 Hydraulic Chipping Hammer

2023-06-27

CB61-120丨Emulsion Band Saw

2020-06-13

AN11-6000 Electric servo CNC Torque Wrench

2023-06-27

AW21-1200 Pneumatic Impact Wrench (Ex-proof Series)

2021-06-15

AN31-20000 Hydraulic Torque Wrench

2023-06-27

DB21-018 Pneumatic Balance Drill

2020-06-13

DH22-030 Pneumatic Hand-held Hammer Drill (AVT series)

2022-12-13

AW21-2000丨Pneumatic Impact Wrench (Ex-proof Series)

2021-06-15

AW21-850丨Pneumatic Impact Wrench (Ex-proof Series)

2021-06-15

CB61-200丨Emulsion Band Saw

2023-06-17

LW21-020 Pneumatic Winch

2023-06-29

CF21-005 Pneumatic Cutter

2022-12-12

LH11-010 Electric Hoist

2023-05-11

DC31-150 Hydraulic Core Drill

2023-01-03

CD22-380 Pneumatic Mining Chainsaw/Pneumatic Concrete Chainsaw (5.0KW)

2023-06-16

AW21-2200丨Pneumatic Impact Wrench (Ex-proof Series)

2021-06-15

DH21-030 Pneumatic Hammer Drill

2021-06-10

CC20-630 Pneumatic Light Chainsaw (3.0 kw series)

2023-06-14

GG11-100 Electric Angle Grinder

2023-06-28

CN22-3241 Nut Cutter丨Split-type Nut Cutter

2023-06-17

CS21-180 Pneumatic Handheld Circular Saw

2020-06-13

CC21-630 Pneumatic Light Chainsaw (3.0 kw series)

2023-06-14

DB21-020 Pneumatic Balance Drill

2023-06-19

RH31-2100 Hydraulic Chipping Hammer

2022-12-27

CC21-380 Pneumatic Light Chainsaw (3.0 kw series)

2023-06-14

CS22-180 Pneumatic Trolley Circular Saw

2021-06-08